A quote for a faucet or garbage disposal is mostly labor, plus the fixture itself, plus whatever the existing plumbing needs before the new part will fit. Prices swing widely, so insist on itemized numbers in writing. For repair-versus-replace advice on sinks and disposals as a whole, start at the fixtures and disposal hub.
What makes up the price of replacing a garbage disposal?
A disposal quote has four parts: the unit, labor, the electrical connection, and any extras such as a new drain trap or a power cord. Units are priced by motor size, so a three-quarter horsepower model costs more than a half horsepower one. The plumber should name the model on the quote, and you should compare like for like.
Ask each bidder for this breakdown:
- Make, model and motor size of the disposal.
- Whether the old unit is hauled away.
- Plug-in cord or hardwired, and who does the wiring.
- A new mounting gasket and drain parts, if the old ones are worn.
- Whether the dishwasher drain gets reconnected and the knockout plug cleared.
Without the first line you cannot compare bids. Without the last, a dishwasher can back up into the sink on the first cycle after the install.
Can a garbage disposal be fixed instead?
Often yes. A hum with no spin usually means a jam, and turning a hex key in the socket on the underside may clear it once power is cut. A dead unit may only need its reset button pressed. Leaks at the top flange, side seam or drain connection are the real question: flange and drain leaks are repairable, a cracked housing is not.
Repair makes sense for a unit under ten years old with a jam, a tripped reset, a loose flange or a bad gasket. It is poor value if the housing leaks, the motor gives off a burned smell, or the part costs nearly as much as a new disposal. See fixing a clogged disposal drain for the jam steps before paying for a call.
Never reach into the grinding chamber, even with the wall switch off. Switch off the breaker feeding the unit before any work on it.
How many years does a disposal normally last?
Households commonly get around eight to fifteen years from a disposal, with the shorter end for heavy use and weak motors. Hard water leaves scale on the grinding parts and housing, and third-party estimates rate Murrieta water as moderately hard to hard, so a unit here may land near the short end. Check your district's water quality report for your own address.
Signs of a unit nearing failure: repeated jams, a rusty smear under the sink, a motor that groans before it spins, and drips from the bottom. Replacing before the leak starts saves the cabinet floor. If the sink base is already soft or stained, tell the plumber, because the damage may be a separate repair.
How long does installing a disposal take?
A plumber who does this often can finish a like-for-like swap in about one to two hours. A first-time installation, where no disposal exists, runs longer since the plumber has to add power, a switch, and sometimes a new drain configuration. A double-bowl sink needs extra tailpiece work, and a single-sink layout is simpler.
Typical sequence: cut power, disconnect the old unit and flange, clean the sink opening, mount the new flange with plumber's putty, hang the unit, attach the drain, join the dishwasher hose, then wire it or plug it in, run water and test for leaks.
Brand makes less difference than most people expect, although each maker supplies its own mounting kit. Moen, GE, InSinkerator and Waste King units mount similarly, and a plumber can fit any of them. Online install videos show the steps, but watching a video does not replace the wiring skill or the leak test, so be honest about your comfort with both.
What about hardwired disposals and air switch buttons?
A disposal either plugs in to an outlet beneath the sink or is hardwired through a switch. Plug-in is simpler to replace. Hardwired units need a correct junction, wire sizing and a switch location, and that is electrical work with its own rules, so ask who will do it and what is included. An air switch button on the counter uses a small air tube to trigger a switch under the sink.
If you want that button, read about air switch disposal installation. In some homes the cabinet already has an outlet that was wired for a disposal, which saves time. Never wire a disposal on a general-purpose circuit that is overloaded.
What does faucet installation cost, and how does shower repair differ?
Faucet installation quotes depend on the faucet, the sink holes, and the condition of the shutoffs. A simple swap with good valves takes under an hour. Old, stuck shutoff valves, corroded supply lines or an undersized sink can double the time. Supplying your own faucet changes the bill, but a bad part is then your problem.
Shower faucet repair is different. A dripping showerhead or valve cartridge swap is modest; opening a tile wall to reach a bad valve body is not. Find out from the plumber if the valve can be serviced from the front or needs access from behind. Cost drivers are cartridge model, wall access and tile repair. See fixing a leaking shower faucet for what a handy owner can try first.
Related reading: faucet replacement cost and the general plumber cost guide.
A contractor license is generally required in California at $1,000 in labor and materials, and for every permit job, so a small install may sit under that line; ask for a license number anyway. Murrieta Creek Plumbing passes your request to nearby plumbing companies, and those that quote pay us a fee for the referral.
Common questions
Why does the same disposal get quoted at very different prices?
Bidders may include different models, wiring, haul-away, or a parts markup, and travel or diagnostic fees may sit on top. Ask each for model, labor hours and fees separately. A quote that only says "install disposal" hides those differences and makes comparison guesswork.
Should I buy the faucet or disposal myself?
You can, and some plumbers accept it, but they may not warrant the part and may charge the same labor. If the part is wrong or defective, you are returning it. Ask first. Buying exactly what the plumber specifies, including the right mounting kit and cord, avoids a second trip.
Is a stuck shutoff valve a common surprise?
Yes. Old angle stops under a sink may seize up or drip when you turn them, and replacing them is often added to the job. A plumber who sees that on arrival should explain the added cost before proceeding. If you can, give them a gentle turn each year to keep them from freezing in place.
Does swapping a faucet or disposal need a permit?
Usually not when the swap is like for like. Adding a new circuit or moving drains may change that. Permit rules vary by office, so ring the City of Murrieta's Building and Safety Division on 951-461-6062 (city page; confirm), or the county office for French Valley and Winchester addresses.
How should I prepare before the plumber arrives?
Empty the sink cabinet, find the house water shutoff in case the local valves fail, and note whether an outlet sits below the sink. Photograph the current setup and any model label, so the correct parts are on the truck for the first visit.
Last changed