Jump to content

Service ยท Murrieta

Rinnai tankless water heater repair in Murrieta

Rinnai units announce most faults with a number on the remote. This page translates the common ones and says where a homeowner's checks end and a plumber's begin.

Get a quote

Tankless heater outline with vent pipe, gas line, water inlet filter, and a code display showing 11.

A Rinnai tankless heater that stops working usually displays a diagnostic code, and Rinnai's own troubleshooting guide ties each number to a short list of checks. Codes 10, 11, 12 and LC cover the majority of calls. This is one of several brand pages under water heater repair, and your model's manual has the final word.

What do the common Rinnai error codes mean?

Per Rinnai's troubleshooting guide: code 10 is an air supply, exhaust blockage or full condensate trap, code 11 is no ignition, code 12 is flame failure, and LC signals lime scale in the heat exchanger. Meanings shift slightly from one series to another, so look in the manual for your exact model.

Four tiles showing tankless codes 10, 11, 12 and LC with short meanings, LC highlighted for scale.

Write the code down before you reset anything. A plumber can tell a lot from which code appeared and whether it repeats. If the code clears and returns within days, the cause is still there.

What does code 11 or 12 usually mean?

Both point to the burner. Code 11 means the unit tried to light and could not. Code 12 means a flame started and then died. Rinnai's list starts with the basics: gas turned on at the heater and the meter, propane in the tank if applicable, the right gas pressure and type, and air bled from the gas line.

You can check the shutoffs and, for propane homes, which some rural lots have, the tank level. Flame rod wiring, gas pressure and grounding belong to a plumber or appliance technician, and any work on the gas line is for a contractor who has a California contractor license. Should you smell gas, leave at once, use the SoCalGas line, 1-800-427-2200, from a safe spot outdoors, and call 911 should you feel threatened.

What is code 10, and what can you check?

Code 10 means the unit cannot breathe or exhaust properly: a blocked or frozen vent, a dirty air filter, a fan problem or, in condensing models, a condensate trap that has filled. Rinnai's guide lists the inlet air filter, vent terminations and condensate drain as the first checks.

From outside you can look at the vent termination for nests, leaves or stucco dust, and clear it if it is safe to reach. Do not open sealed vent joints. A trap clogged with debris is a straightforward cleanout for a plumber but a repeating code 10 suggests something in the venting needs attention.

Why does the LC code show up in Murrieta?

LC means mineral scale has accumulated inside the heat exchanger. Third-party estimates put Murrieta water around 6 to 11 grains per gallon, which is moderately hard to hard, making scale a realistic cause, though the number at your address may differ. Which district serves you is on your water bill.

Rinnai's guidance is to descale by running a flush via the unit's service valves, then reset the power to clear the code. Manuals disagree on whether the unit keeps running while LC is displayed, so check yours. After a flush, a softener upstream can slow the return. For the softener side, see installing a water softener.

What details help when you request a Rinnai repair?

Collect the model number from the unit's label, the code on the remote or display, the date it first appeared and whether a reset clears it. Say whether the unit is indoors, in a garage or outside, and whether it burns natural gas or propane. With a phone photo of the unit and its vent, the plumber can arrive with suitable parts and quickly see whether scale, venting or gas is the likely culprit.

What else makes a Rinnai heater run cold or cycle?

Low flow, clogged inlet screens, a failing flow or temperature sensor, a gas line undersized for the unit, or a recirculation loop that cools the water are common. If the unit works at one tap but not another, the unit is probably fine and the plumbing or a mixing valve elsewhere is the cause.

Many problems fall into one of the groups on the tankless service and repair page. A heater that fails outright with water on the floor needs emergency water heater repair. If a heater that shows no code still gives too little hot water, read shower with no hot water.

Should the Rinnai be replaced instead?

Think about it if the heat exchanger is cracked or leaking, if repairs are nearly as expensive as a new unit, or if the model is old and parts are scarce. A heater that has never had a flush in hard water may fail sooner than one that has.

For installation planning see Rinnai installation, and for general guidance on the work and what drives price see tankless installation cost. Water heater replacements normally need a permit through the City of Murrieta, Wildomar or the county, which the plumber arranges.

Ask for a written plumber quote

A few details and we'll set up a visit from a local plumber specialist, then a written quote.

Lets the business see where the job is before they quote.

We earn a referral fee from the plumber who takes on your job. You pay us nothing.

Common questions

Can I reset a Rinnai tankless heater myself?

Yes. Cut power at the unit or the breaker for a minute, then restore it. This clears many temporary codes. If the same code returns, resetting is not a repair. Write down the code and the date, and keep it handy when you request a visit.

How often should a Rinnai be flushed?

Rinnai guidance and the manual call for periodic descaling, and more often where water is hard. For Murrieta homes, a yearly flush is a common rule of thumb, but follow your manual. A unit showing LC needs a flush now. Service valves on the water lines make it easy.

Do I need a special plumber for Rinnai?

Not special, but one who works on tankless units regularly diagnoses faster. Ask about the brand when you book. Rinnai makes several series with different controls and different code lists, so tell the plumber your model number from the data label, plus the code and when it began.

Does the warranty still apply if a plumber repairs it?

Warranty terms depend on the model, the installation and the maintenance record, and we cannot state them. Read your paperwork or contact Rinnai. Keep receipts for flushes and repairs, since a service record often matters if you need to claim.

How does a plumber get arranged through this site?

Use the quote page to share your details, and we hand them to a local plumbing business. Such businesses pay this site a fee for requests they accept, and the one you get does the repair under its own name. Read how it works or go back home.

References

Last changed