When hot water is missing everywhere, the fault is at the heater or what feeds it. When only one tap stays cold, inspect that tap or its pipe. Start with the heater itself: is it on, is it fueled, is the breaker up, is the pilot lit, and is there a fault code on the display? Once you know which part is bad, water heater repair explains the fixes.
Which checks come first once the hot water stops?
Check the power or fuel before anything else. With an electric tank, inspect the breaker and the red reset button under the upper thermostat cover. With a gas tank, see whether a pilot flame or a lit display is present. With a tankless unit, read out the error code. A thirty-second check clears a surprising number of calls.
Quick order of checks:
- Is it one tap or all taps? A single tap points to a faucet cartridge or a mixing valve. Related guides cover a cold kitchen tap and a shower that runs cold.
- Is the heater powered? Breaker, switch, and a gas valve handle lined up with the pipe.
- Is the water shutoff to the heater open? A cold supply closed after a repair stops flow.
- Is the thermostat set above warm? Kids and cleaners bump dials.
- Any water on the floor? That points to a leak rather than a heating fault.
If the heater is running but the water never gets hot, the picture differs, covered on the heater is on but the water stays cold.
Why would a gas heater lose its heat?
The usual causes are a pilot that blew out, a thermocouple or flame sensor that no longer proves the flame, a clogged burner or a gas supply interruption. Combustion air matters too, since a heater starved of air in a closed closet can shut itself down. A worn thermocouple is the cheap and frequent culprit.
Relighting a pilot follows the manufacturer's instructions, which you will find on a label on the heater. Stop trying if the pilot refuses to stay lit, because a heater that keeps losing its flame has a fault. A gas odor means walking out at once, ringing SoCalGas at 1-800-427-2200 from outdoors, and dialing 911 if you feel in danger. Touch no switches on the way out.
Gas in Murrieta, Wildomar and the surrounding Riverside County communities is expected to come from SoCalGas where your street has service, while some rural homes run on propane or electricity, so check which fuel you have before you troubleshoot. For the part itself, see thermocouple replacement.
Why would an electric heater give only cold or lukewarm water?
Electric tank heaters use two heating elements and two thermostats. If the upper element fails, you get no hot water. If only the lower element fails, you get a little hot water that fades quickly. A tripped high-limit switch or breaker can cut both. Elements wear out, especially in hard water areas where scale coats them.
Third-party estimates rate Murrieta tap water as moderately hard to hard in general, so element scale is a normal wear cause here, and it is worth checking your district's report. Testing an element requires a meter and turning off power at the breaker first. Water and electricity together are a shock hazard, so if you are not sure, leave it. See replacement water heater element for the detail.
Could it be the tankless heater?
Yes. Tankless units fail on a flow switch, a scale-clogged heat exchanger, an igniter, a blocked vent or an error that needs a reset, and they will not fire at all if the flow is too low. When the display gives a code, write it down and look it up in the manual, then call a plumber if it repeats.
Tankless is also sensitive to hard water, which is why a regular flush matters. ENERGY STAR gives about 20 years as a life expectancy for gas tankless, assuming upkeep. If the unit runs but the water stays lukewarm, check the flow rate and whether two fixtures are drawing at once. Brand repair pages: Rinnai, Navien, Noritz, Rheem.
Does a lack of hot water count as an emergency?
That depends. At home it is an urgent nuisance but usually not an emergency, unless there is a gas smell, water spreading over the floor, a heater that is hot to the touch or buzzing, or a vulnerable person in the house. For renters, California's habitability law names hot running water among the things a landlord must supply, so the landlord has a duty.
Treat any of these as urgent: water pooling, gas odor, scorched or melted wiring, or a relief valve spewing water. Close the cold feed into the heater, switch off its fuel or power, and call. For after-hours help, see emergency water heater repair.
Renters should write to the landlord, hold on to a copy, and allow time to arrange repair. For apartment buildings with a shared boiler, the building manager handles it, not you.
Who do I call if the hot water stops?
For a house you own, call a plumber, or an HVAC business if your hot water comes from a combined heating unit, such as a boiler or a combination system. Give them the fuel, brand, age and the checks you have done already. For a rental, start with the landlord or property manager.
It is reasonable to ask for a written quote before work, the part number and the contractor license number of the plumber. To get a visit arranged, send a price request with the heater's brand and age, and what the display or pilot is doing. We forward it to a nearby plumbing company, and the companies that take requests pay us a fee. Our other services are on the plumber home page.
Why do I hear noises from the heater, and what about tankless dislike?
Rumbling or popping from a tank is the sound of steam bubbling through sediment. It points to scale and a tank due for flushing or replacement. Hissing may be water dripping on a hot surface. Plumbers' complaints about tankless units are practical, not ideological: they cost more up front, need correct gas and vent sizing, and require descaling where water is hard.
That is the whole story behind "plumbers do not like tankless". Where they are installed well and maintained, they run for years. Where gas lines are undersized or venting is wrong, they trip errors. See tank versus tankless.
Common questions
How much time should I spend troubleshooting first?
Spend about ten minutes on the simple checks: breaker, pilot, thermostat, shutoff valve. If the heater trips again or shows a repeat error, stop and call. Do not wait if you smell gas, see water spreading or notice scorching, since those are not troubleshooting jobs.
What signs show the heater is worn out?
Rust-tinted hot water, moisture at the base, rumbling that returns after flushing, repeated element or thermocouple failures, and age beyond roughly 10 to 15 years all point to replacement. A leak from the tank shell cannot be repaired. For timing, see water heater replacement intervals.
Can a leak elsewhere cause no hot water?
Yes. A hot line leak can drop pressure, or lose heated water into a wall or slab before it reaches the tap, and the heater then runs constantly. A high gas or power bill with weak hot water is a clue. Ask a plumber about leak detection if you suspect it.
References
- California Civil Code section 1941.1, habitability of rental dwellings
- ENERGY STAR, gas tankless water heater benefits
Last changed